Does phantom power hurt Shure SM58?
No. Any dynamic microphone with a low impedance balanced output, like the SM58, is not affected by phantom power. Phantom Power will not damage a professional dynamic microphone.
Do I need preamp for Shure SM58?
Dynamic Mics (like the Shure SM57 and SM58) are designed to handle very loud sound sources without distorting. They’re designed to be shouted into without generating a signal that would clip a mic preamp.
Does my mic need phantom power?
Put simply, condenser microphones have active electronics that need an external power source, while dynamic mics are passive and therefore do not need phantom power. Because of the way condenser mics work, their output is very high impedance, and therefore requires a powered circuit to reduce that impedance.
Do all mics need 48v?
Most mics work fine over the voltage range of 12-48 volts, although many mic manufacturers specify 48 volts for best performance, and some mics may be more problematic than others when encountering lower levels of phantom power—you may notice some loss of output or sensitivity with lower voltages.
Why is my Shure SM58 so quiet?
Many people experience the issue of a dynamic microphone such as a Shure SM7b or SM58 that is too quiet; why does this happen, and how do you fix it? Low volume output from a dynamic microphone is usually due to low gain levels, poor microphone placement, and the lack of supporting hardware such as a preamp.
Can you use a condenser mic without phantom power?
Although there’s no way to use a condenser mic without phantom power, you can use a condenser mic without an audio interface, or mixing board, straight to your computer. To do that you need you need an XLR to USB pre amp, such as the MXL Mic Mate Pro.
Does SM58 need FetHead?
it’s a dynamic mic that does not use phantom power. Answer: You need the normal FetHead. The SM58 does not have a very low output level, and Julian is testing with an SM7B, which has a VERY low output level, so the benefit of the FetHead is even more important.
Why is my Shure SM58 quiet?
Will phantom power hurt a mic that doesn’t need it?
Phantom requires a balanced circuit in which XLR pins 2 and 3 carry the same dc voltage relative to pin 1. A balanced dynamic microphone is not affected by phantom power; however, an unbalanced dynamic microphone will be affected. Although the microphone will probably not be damaged, it will not work properly.
How do I make my SM58 louder?
Infact the transformer in the sm58 should actually make the signal louder than other dynamics. Either just amplify the thing digitally or with a mixer. You don’t need something like a fethead unless you are doing live vocals.
Is Shure SM58 low or high impedance?
The SM58 is low impedance. If you connect the SM58 to a Shure A85F low-to-high impedance transformer, it will be as loud, if not louder than the PE515. In general, a high impedance microphone will have an output level around 20 dB greater than a low impedance microphone.
What happens if you don’t use phantom power on a condenser mic?
Although you may still get a signal from some condenser mics without phantom power, it will be so weak that it will be barely audible. In most cases, you won’t get a signal at all. Condenser mics need power to operate correctly whether that be battery or phantom power.
What’s the difference between the SM58 and the beta58a?
What’s the Difference Between the SM58 and the Beta58A? Polar Pattern: Perhaps the most obvious difference is the microphone polar pattern. Output Level: Due to its neodymium magnet, the Beta 58A has greater sensitivity and a 4dB hotter output than the SM58. Frequency Response: The Beta58 has an extended low-end and high-end compared to the SM58.
What are the main characteristics of the Shure SM58 microphone?
SM58 Dynamic Vocal Microphone Roll with no shake or rattle. Handling noise gets absorbed by the pneumatic shock mount, keeping the sound free of vibration. Screen out unwanted air. When wind and plosives try to take over, the spherical mesh grille and built-in pop filter keep them out of the mix. Rugged for the road ahead. Taking the show on tour?
Do dynamic mics need Phantom Power?
Put simply, condenser microphones have active electronics that need an external power source, while dynamic mics are passive and therefore do not need phantom power. Because of the way condenser mics work, their output is very high impedance, and therefore requires a powered circuit to reduce that impedance.
What is phantom power mic?
Phantom power is a way of providing your mic with enough DC voltage (48v to be exact) to function, which is something that it can’t do if it’s just connected to your computer. Essentially, phantom power transmits the right amount of voltage and audio simultaneously over a single cable.