How do I reset my ASA to factory settings?

Solution

  1. Connect to the ASA via the console Cable.
  2. log in and go to configure terminal mode.
  3. Execute the following command “config factory-default”
  4. Press the space bar a few times to execute the commands.

How do I reset my ASA 5505 without a password?

  1. Step 1 Connect to the adaptive security appliance console port according to the instructions in “Accessing the Command-Line Interface” section.
  2. Step 2 Power off the adaptive security appliance, and then power it on.
  3. Step 3 After startup, press the Escape key when you are prompted to enter ROMMON mode.

How do I save ASA configuration?

Save running config on Cisco device Use the command copy running-config startup-config (copy run start) to overwrite the current startup config file with what is currently in the running configuration file.

How do I reset my ASA 5510 to factory settings?

Resetting a Cisco ASA 5510 to Factory Defaults

  1. Connect your console cable and make sure you can see the command prompt for the ASA – even if you can’t log in.
  2. Power cycle the appliance – flick the power switch on the front off and on again.

How do I restart Sftunnel?

Any easy way to restart the sftunnel channel services would be by using the manage_procs.pl script and selecting option 3. Once the services restarted you can exist selecting option 0.

How do I unregister from FTD FMC?

You do not need to unregister the other FMC.

  1. Log into the Firepower Management Center.
  2. Step 2 Choose System > Licenses > Smart Licenses.
  3. Next to Smart License Status, click the stop sign ( ).
  4. Step 4 Read the warning and confirm that you want to unregister.

How do I reset my ASA password?

To recover passwords for the ASA, perform the following steps:

  1. Step 1 Connect to the ASA console port according to the instructions in “Accessing the Command-Line Interface” section.
  2. Step 2 Power off the ASA, and then power it on.
  3. Step 3 After startup, press the Escape key when you are prompted to enter ROMMON mode.

How do I find my startup-config?

To display the startup configuration, enter the show startup-config command. Enter the copy startup-config running-config command to write the startup configuration to the running configuration. Warning This command sequence will erase the entire RPM configuration in RAM and NVRAM and reload the RPM.

How erase Cisco ASA config?

With [ciscoasa# write erase] you will erase configuration file in flash startup-configuration. After this use reload on ASA. You will get cleared ASA configuration file, without DHCP Server any interface configured no ip addresses or NAT as you will get with factory default restart.

Which is the default configuration for Cisco ASA 5505?

For the ASA 5505 adaptive security appliance, the factory default configuration configures interfaces and NAT so that the security appliance is ready to use in your network immediately. The factory default configuration is available only for routed firewall mode and single context mode.

How to enable flow control on Cisco asa5505?

Flow control: None After you open your connection, press enter a couple times, and you should get a prompt like: ‘ciscoasa>’, or ‘nameofyourdevice>’ type ‘ena’ to go to enable mode. Enter the password, or just press enter if there is no password set.

How to force ASA to read its startup configuration on boot?

While still in Configuration Mode, reset the configuration register to the default of 0x01 to force the security appliance to read its startup configuration on boot: asa (config)#config-register 0x01 12. Use the following commands to view the configuration register setting: asa (config)#exit asa#show version

How to restore default configuration in Cisco Security Appliance?

To restore the factory default configuration, enter the following command: If you specify the ip_address, then you set the inside or management interface IP address, depending on your model, instead of using the default IP address of 192.168.1.1. The http command uses the subnet you specify.