What do I do when my Samsung printer says paper jam but there is none?

If your Samsung printer says paper jam but there is none, you can usually fix it by cleaning it. A Google search turned up some weird advice, including changing your USB cable, or moving it to a different port. Whatever. Someone suggested replacing the pickup roller.

Why does my Samsung printer keep jamming?

The most common cause of paper jams is the paper; please check the user manual to make sure the media being used is recommended for the printer. Also, make sure the printer and driver setting match the paper type. When the printer displays Jam 2, the paper has failed to pass through the paper exit area.

When there is a paper jam in printer 2?

Step 2: Clear a jam from the inside of the printer

  • Turn off the printer.
  • Disconnect the power cord and any other cable.
  • Remove jammed paper from the following areas.
  • Replace any parts that were removed, and close any open doors.
  • Reconnect the power cord, and other cables that were disconnected.
  • Turn on the printer.

How do you fix a paper jam issue?

Remove the paper following the procedure below.

  1. Slowly pull the paper out, either from the Rear Tray or from the Paper Output Slot, whichever is easier.
  2. Open the Rear Cover.
  3. Pull the paper out slowly.
  4. Close the Rear Cover.
  5. Reload the paper, and press the RESUME/CANCEL button on the printer.

Why does my printer says paper jam when there isn’t one?

your pickup roller is dirty and the printer can’t grab a piece of paper. it will say paper jam when it does this. get a drop of dishsoap and clean the pickup roller of your printer with this.

Why does my printer keeps jamming?

If your printer keeps jamming, you should know that the most common cause of a jam is misalignment of the paper. Paper needs to load in smoothly, completely flush with the tray. Overfilling the tray is a great way to ensure you will be spending some personal time getting to know the inside of a printer.

Why does my HP printer keep saying paper jam?

your pickup roller is dirty and the printer can’t grab a piece of paper. it will say paper jam when it does this. get a drop of dishsoap and clean the pickup roller of your printer with this. scrape at it with your fingernail to get the roller clean and wipe it off with a damp washcloth.

How do you remove a paper cassette from selphy?

Slide the translucent top cover of the Paper Cassette back to expose the paper storage area. With the top half pulled back, lift the glossy side and open the Cassette.

How do I clean my Selphy printer?

Cleaning the Inside of the Printer (SELPHY ES3 / ES30)

  1. Remove the ink cassette. Open the ink cassette compartment cover.
  2. Insert the cleaner stick all the way in the ink cassette compartment and slide it in and out 2 or 3 times. Important!
  3. Replace the ink cassette and try printing again.

How to fix Paper Jam on Samsung clx-3175 printer?

The fuser can be removed start pulling on its right side. Then the printer should look a bit empty and we can see the Paper Exit Sensor in the upper right corner: To remove the cables from the sensor, it is necessary to remove the High Voltage board on the left site (from front) of the printer.

Where is the paper exit sensor on a Samsung clx-3175?

The problem is a Paper Exit Sensor with part number 0604001393 which can be ordered for about 6-10€. It’s a simple IR light barrier which is located top-right above the fuser (seen from the backside of the printer). I think the sensor gets broken because it can’t stand the heat of the fuser.

What should I do if my printer is jammed?

Gently pull any visible jammed paper. Close the multi-purpose (manual feeder) tray. Open the multi-purpose (manual feeder) tray. Gently pull any visible jammed paper. Close the multi-purpose (manual feeder) tray. If the paper is jammed inside the printer, use the handle to completely open the access door.

How to get paper out of Samsung Printer?

Pull tray out Tray1 by handle. If jammed paper is visible, gently pull it straight out. Once the paper is removed, close Tray1. Pull optional Tray2 out by handle. If jammed paper is visible, gently pull it straight out. Once the paper is removed, insert Tray2 back into the printer until it snaps into place.