What UTM zone is Colorado?

Therefore, Denver, Colorado, is in UTM Zone 13. World UTM Zones. Source: GPS for Land Surveyors. All UTM zones have a width of 6° of longitude. From north to south the zones extend from 84° N latitude to 80° S latitude.

How do I find my UTM zone?

So for example, the UTM zone number for 39° W would be found through these steps: -39 + 180 = 141. 141 / 6 = 23.5. 5 rounds up to 24….Option 1 – The Mathematic Approach

Take your longitude coordinate in decimal degrees and add 180.
Then divide by 6.
Finally round-up to the next highest whole number.

How do I find my UTM grid reference?

To find the UTM coordinate of a point, “read right up”. The numbers designating the vertical gridlines (at the bottom or the top of map) are the easting values. The numbers to the sides of the map labeling horizontal lines are the northing values. In the map example below, grid lines are 1000m apart.

Are there 120 UTM zones?

UTM zones are six degrees wide. Each zone exists in a North and South variant. Universal Transverse Mercator Zone n (N) – The Northern Hemisphere projections for the infamous UTM system consisting of 120 zones (60 different zones with North and South variants of each).

What is UTM map?

UTM is the acronym for Universal Transverse Mercator, a plane coordinate grid system named for the map projection on which it is based (Transverse Mercator). The UTM system consists of 60 zones, each 6-degrees of longitude in width. One system is no more or less accurate than the other.

What is the difference between WGS84 and UTM?

The difference is that WGS 84 is a geographic coordinate system, and UTM is a projected coordinate system. Geographic coordinate systems are based on a spheroid and utilize angular units (degrees).

What is Zone UTM?

How do I read a UTM map?

When reading a UTM coordinate, your reading should state latitude and then longitude (eastings first, then northings). A useful mnemonic to help you remember this is “along the corridor, then up the stairs.” To unpack these numbers, we have to break the reference down into parts: 18—The zone number.

What is the difference between UTM and Latitude longitude?

The Universal Transverse Mercator (UTM) is a map projection system for assigning coordinates to locations on the surface of the Earth. However, it differs from global latitude/longitude in that it divides earth into 60 zones and projects each to the plane as a basis for its coordinates.

Where are the UTM zones in Denver Colorado?

For example, Denver, Colorado is near 105° W. Longitude, –105°. Therefore, Denver, Colorado, is in UTM Zone 13. All UTM zones have a width of 6° of longitude. From north to south the zones extend from 84° N latitude to 80° S latitude. Originally the northern limit was at 80° N latitude and the southern 80° S latitude.

How many UTM zones are there in Australia?

Within continental Australia, there are 8 UTM Zones, numbered 49-56 going from west to east (see Figure 1). As shown in Figure 2, there are two zones in the Northern Territory zones 52 and 53, with Darwin falling in zone 52, and the Alligator Rivers Region primarily within zone 53.

Which is UTM Zone 13 Universal Transverse Mercator?

Universal Transverse Mercator. Therefore, Denver, Colorado, is in UTM Zone 13. As you notice a Universal Transverse Mercator zone embraces a much larger portion of the earth than does a state plane coordinate zone. When you get a larger bite, a larger portion of the earth, the scale factor is less attractive.

What are the zones in the Northern Territory?

As shown in Figure 2, there are two zones in the Northern Territory zones 52 and 53, with Darwin falling in zone 52, and the Alligator Rivers Region primarily within zone 53. The correct way to refer to these zones is as the ‘Map Grid of Australia (1994), zone 53 (or 52)’.